ISO Approved Warehouse Storage Drawer Type Mould Rack with Full
Unisource Mold Storage Rack is mainly used for storage of all kinds of mold, Dies, Toolings
and any tpe of Parts. They could be assembled with manual movable
carriage on the top so as to easily take and retrieve the goods.
The side rack was equipped with idler wheel rail on the bottom and
the sliding shelf panel could be freely pulled out when loading.
The middle type slide rack could carry less than 800KG/Layer, The
entire drawer type mold storage rack is section combination structure, which is convenient for
transport, and the assembly is simple and fast and this rack
possesses better safety protection device. Special drawer type mold
rack can be ordered. Get a quote today.
1. Add additional fixing equipment, can be used safely;
2. Easy operation: with bearing assembly, sliding easy and can work
with crane devices;
3. Save space and cover less area, 3*4 standards shelf can be
deposited with dozens dies;
4. Simple structure: composed by a variety of components, easy for
transport and assembly;
Quick Specification of Mold Storage Racks:
|Item number||Drawer Mold Rack, Sliding Rack, Tooling Rack|
|Material||High Grade Hot Rolled Q235B or Q345|
|shelf||Draw-able, can be half open or widely open|
|Standard size||L3000*W625*H2000mm,L1385xW800xH2000 can customized any size|
|Level & Loading Capacity||4 The top level is fixed and its loading capacity is equal to or
bigger than 1000kg. The lower three levels can be drawn out 500mm
and can load as much as 1000kg.|
|Drawer mold rack using||Storage mold / Die / Heavy Duty Accessories / Parts|
|Surface treatment||Powder coated|
|color||Green or as customized|
|upright post||100*50MM square tube, #10 channel steel|
|upright post spacer||2.0MM cold roll steel|
|Drawer material||2.0MM cold roll steel|
|Accessories||overhead traveling crane and chain block|
Note:The lower three levels can only be drawn out one by one.(when first
level is drawn out. The second and third level can not be drawn
out. This is because of the self-locked system. We design this
system to protect the whole rack in stable situation and safe.
Unisource Mold Storage Racks Components:
1.Travelling Crane Arm
2.Front Crane Rail
3.Rear Crane Rail
Mould rack is composed of upright frame, steel decking, support
structure, self locking devices etc,
The support structure is the secondary design, the loading capacity
of the single drawer is generally within 1000KG.
The drawer decking can be designed to the semi-open.It is suitable
for storing molds etc, the crane, forklift, self-made trolley can
be used for picking up goods.The particular slide-way design makes
the small using resistance, and the self-locking device can be
reliable, and safe.,Each drawer can be drawn out 60% of its depth.
Slide rack is widely used in work plants of machinery industries.
To work with crane will enhance the work efficiency. For tools are
often very heavy and small in size, so the draw-out design makes
tools easier be taken out. So it makes access work convenient.
3~10 years warranty in case that
A) Proper handling during operation, correctly forklift handling
B) Overloading is prohibited
C) Environment request –indoor, dry and not humid circumstance, do
not contact with any corrosive chemical material (for zinc plated
and powder coated products, no limitation for hot dip galvanized)
D) We will take full responsibility for any manufacturing defect is
identified after arrival, would either refund or reship good
products to you.
Get a quote today:
- Drawing (if available) of rack; if not, we can offer CAD design
service for you
- Size of your warehouse (Length x Width x Clear height)
- Storage requirement on the cargo(temperature etc)
- Size (W*D*H) & weight of pallet (after loading)
- How many pallets each layer you would like
- How many layers you would like
- Parameter of your forklift ( to decide the width of aisle between
- The color you want